DAMPA Clip In Tile (English) - Catalog - Page 7
7
8
Carrier
Splice No. 4 is centrally positioned
over the joints in the carriers.
The hanger distance from the joints must
not exceed 500 mm.
A gap of 2-4 mm should be maintained to
allow for expansion.
9
By direct installation Carrier No. 4 is
fastened on alternately sides with suitable
screws directly to the soffit and thus only
Edge Trim No. 11 can be used.
The single system can also be used.
It consists of parallel carriers.
Each carrier is supported by hangers.
Max. distance Aluminium
A 1000 mm
B
2000 mm
Steel
900 mm
1800 mm
Floating Ceiling Areas
min. 188
67
38
10
is possible to remove and reinstate
It
individual tiles anywhere in the ceiling.
To remove, insert the dismantling tool up
into the tile joint close to the corner and
pull down gently.
Minimum Constructional Height
The suspended DAMPA® Clip-In tiles have a
minimum constructional height of 188 mm.
The minimum constructional height of
DAMPA® Clip-In Tiles installed direct to the
soffit is 38 mm.
As perimeter solution Carrier No. 10
is used for full tiles.
Edge Trim No. 11 is is used for cut
tiles.
In the primary grid system both upper
and lower carriers are secured by
means of screws or pop rivets to the
edge solution.
To secure stability the maximum
distance from the edge solution to
the upper carrier must not exceed
200 mm.
Modules
DAMPA Clip-In/Aluminium
DAMPA Clip-In/Steel
Module 300 × 600 mm, material thickness 0.7 mm
Module 500 × 500 mm, material thickness 0.7 mm
Module 600 × 600 mm, material thickness 0.7 mm
Module 24 × 24 inch, material thickness 0.7 mm
Module 300 × 600 mm, material thickness 0.5 mm
Module 500 × 500 mm, material thickness 0.5 mm
Module 600 × 600 mm, material thickness 0.5 mm
Product
Carrier No. 4
Carrier Splice No. 4
Coupling Clip No. 1
Adjustment Clip No. 4
Hanger No. 5
(suspended 500 mm)
Edge Trim No. 11
Product
Carrier No. 4
Carrier Splice No. 4
Coupling Clip No. 1
Adjustment Clip No. 4
Hanger No. 5
(suspended 500 mm)
Edge Trim No. 36 /
Shadow Gap Edge Trim No. 6
Wedge No. 4 / No. 5
Average Consumption
2.00 m/sq. m
1.20 units/sq. m
1.00 unit/sq. m
0.50 unit/sq. m
0.25 m/sq. m
Packing
10 units/bundle
250 units/box
200 units/box
250 units/box
100 m/coil
1.00 m/sq. m
10 units/carton
Module 300 × 300 mm, material thickness 0.5 mm
Product
Carrier No. 4
Carrier Splice No. 4
Coupling Clip No. 1
Adjustment Clip No. 4
Hanger No. 5
(suspended 500 mm)
Edge Trim No. 11
Average Consumption
4.00 m/sq. m
2.20 units/sq. m
2.00 units/sq. m
0.50 unit/sq. m
0.25 m/sq. m
Packing
10 units/bundle
250 units/box
200 units/box
250 units/box
100 m/coil
1.00 m/sq. m
10 units/carton
Average Consumption
2.25 m/sq. m
1.60 units/sq. m
1.10 units/sq. m
0.60 unit/sq. m
0.30 m/sq. m
Packing
10 units/bundle
250 units/box
200 units/box
250 units/box
100 m/coil
1.00 m/sq. m
10 units/carton
2.85 m/sq. m
200 units/box
Module 300 × 300 mm, material thickness 0.5 mm
Product
Carrier No. 4
Carrier Splice No. 4
Coupling Clip No. 1
Adjustment Clip No. 4
Hanger No. 5
(suspended 500 mm)
Edge Trim No. 36 /
Shadow Gap Edge Trim No. 6
Wedge No. 4 / No. 5
Average Consumption
4.25 m/sq. m
2.30 units/sq. m
2.10 units/sq. m
0.60 unit/sq. m
0.30 m/sq. m
Packing
10 units/bundle
250 units/box
200 units/box
250 units/box
100 m/coil
1.00 m/sq. m
10 units/carton
2.85 m/sq. m
200 units/box