Visit Installers guide EN - Flipbook - Sida 11
VISIT TRANSMITTERS
Visit door transmitter
BE1411
Optimizing the doorbell detection
Default signal pattern
The next step is to teach the transmitter to recognize your doorbell.
When the door transmitter is activated, the following happens:
1 Press and hold button 1 until the top LED starts to blink. Release it to start the recording.
1 The LED on the transmitter lights up in green to show that it’s signalling the receiver.
2 For door buzzers (with continuous sound): Press and hold the doorbell for at least 8 seconds.
For door chimes (with a "ding-dong" sound): Press the doorbell at least 8 times.
2 The Visit LED on the receiver lights up in green and it starts to sound, flash or vibrate with a certain pace, called signal
pattern. The transmitter and the connected accessories determine the signal pattern. The default is as follows:
3 Press button 1 on the transmitter to stop the recording. If the LED lights up in red, you need to repeat steps 1 and 2.
If you have an intercom, use button 2 and follow the steps above to record its sound.
Transmitter
Receiver signal pattern
Source
LED
LED
Sound
Vibration
Internal microphone
Green, top
Green light
1door chime, low
Slow
Yes
External microphone
Green, bottom
Green blinks
2door chime, high
Slow
Yes
Connected doorbell
Green, top
3green blinks
1door chime, high
Slow
Yes
Note: To delete all recorded sounds, press and hold button 1 and 2 simultaneously for 5 s. All radio key settings and
signal settings are kept intact.
1
2
3
OK
Try again
Testing the connection
Using the test button
Using the doorbell or intercom
1 Press both test buttons simultaneously on the door
transmitter. The top LED lights up in green to show that
a radio signal is being transmitted.
1 Press the button on the doorbell or intercom.
The LED on the transmitter lights up in green to show
that the sound is detected.
2 The green Visit LED on the receiver lights up to show
that the signal was received. In addition, it starts to
sound, flash or vibrate depending on the receiver.
2 The green Visit LED on the receiver lights up to show
that the radio signal was received. In addition, it starts to
sound, flash or vibrate depending on the receiver.
Note: If you have changed the signal pattern, it will react
in accordance with the table on the following spread.
1
9
2
Note: If you have changed the signal pattern, it will react
in accordance with the table on the following spread.
1
2
Flash
Changing the signal pattern
The transmitter controls the signal pattern. Open the transmitter front cover and move the
signal switches according to the table below to change it:
On
Off
Transmitter
Receiver signal pattern
Switch
Source
LED
Sound
Vibration
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
Green light
Green blink
3green blinks
1door chime, low
2door chime, high
1door chime, high
Slow
Slow
Slow
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
2green blinks
3green blinks
Green blinks
2door chime low
1door chime, high
2door chime, high
Slow
Slow
Slow
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
3green blinks
2green blinks
3orange blinks
1door chime, high
2door chime, low
Baby melody
Slow
Slow
Fast
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
Green blinks
Green light
Orange blinks
2door chime, high
1door chime, low
Baby melody
Slow
Slow
Fast
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
Green light
3green blinks
2green blinks
1door chime, low
1door chime, high
2door chime, low
Slow
Slow
Slow
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
Green light
Green blinks
Yellow blinks
1door chime low
2door chime, high
2ring signal, high
Slow
Slow
Medium
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
3green blinks
Green light
Red + orange light
1door chime, high
1door chime, low
Emergency siren
Slow
Slow
Long
Yes
Yes
Yes
Int. mic. / learned signal 1 / test
Ext. mic. / learned signal 2
Connected doorbell
Green blinks
2green blinks
Red blinks
2door chime, high
2door chime, low
Fire horn
Slow
Slow
Long
Yes
Yes
Yes
Flash
10