Visit Installers guide EN - Flipbook - Sida 50
VISIT RECEIVERS
Visit portable receiver
BE1450
Getting started
Buttons and controls
Power LED Volume Flash LEDs Visit LEDs
Flash signal switch
BE1270 Bed shaker
1 Slide open the battery cover, fit the batteries and close the cover again.
Place the receiver on a level surface or mount it on the wall using the wall bracket.
2 To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter.
3 The receiver lights up a Visit LED and starts to flash and sound. If a bed shaker is connected, it will vibrate.
A short press on the test button repeats the last indication. If nothing happens, see Troubleshooting.
1
Test button
Recesses for wall bracket
Battery compartment
Optional power supply
Technical specifications
In the box
Dimensions and weight
Output
BE1450 Portable receiver
Height: 165 mm, 6.5"
41.5V LR14 batteries
Width: 130 mm, 5.1"
Wall bracket
Depth: 36 mm, 1.5"
Adjustable sound signal
Max 93 dBA @ 1 m, frequency
range: 500 – 1000 Hz
Screws and wall plugs
Weight: 590 g, 20.8 oz. incl. batteries
Bed shaker outlet: 2.0 – 4.0 VDC
Power and battery
Visit LEDs
Frequency and coverage
Mains power
7.5 V DC / 1500 mA
Optional power supply unit
Battery power: 41.5 V LR14
alkaline batteries
Operating time: 2 – 3 years with
alkaline batteries
Power consumption: Active: 1000 mA
Idle position: 0.1 mA
The Visit LEDs normally indicate
the following:
Frequency: 433.92 MHz or 868.3
MHz, depending on region
Orange LED, pacifier symbol
The baby monitor is activated
Coverage by region:
433 MHz: 30 – 80 m (98 - 260 ft)
868 MHz: 50 – 250 m (55 - 273 yd)
Coverage depends on the radio
frequency, building’s characteristics
and the combination of transmitters
and receivers.
Environment
Operating temperature:
0° to 35° C, 32° to 95° F
Relative humidity: 15% to 90%,
non condensing
49
Green LED, door symbol
The door transmitter is activated
Yellow LED, telephone symbol
The phone transmitter is activated
Red LED, fire symbol
The smoke alarm is activated
Orange and red LEDs blink alternately
The CO alarm is activated
Accessories
BE1270 Bed shaker
Bellman & Symfon power supply
unit for Europe or UK
2
3
Default signal pattern
When a transmitter is activated, the receiver lights up an LED, sounds, flashes and the bed shaker starts to vibrate with a
certain pace. This is called signal pattern. The transmitters determine the pattern, and the default is as follows:
Transmitter
Portable receiver
Activated source
Visit LED
Sound
Flash
Vibration
Green
Yellow
Orange
Red
Orange and red
Door chime
Ring signal
Baby melody
Fire horn
Emergency alert
Yes
Yes
Yes
Yes
Yes
Slow
Medium
Fast
Long
Long
Door transmitter / push button transmitter
Telephone transmitter
Baby monitor
Smoke alarm
CO alarm
Bed shaker
Changing the signal pattern
The signal pattern can only be changed on the transmitters. See Changing the signal pattern for the relevant transmitter.
Adjusting the volume and flash
Adjust the volume to your liking using the red volume dial on the top of the receiver. It goes from 0 to 93 dBA @ 1 m with a
main frequency range of 500 – 1000 Hz. Use the flash signal switch on the back of the receiver to turn the flash off/on.
Replacing batteries
If the power LED is yellow when the receiver is activated, the batteries are nearly depleted. Here is how you replace them:
Slide open the battery cover. Replace the old batteries with four new 1.5 V LR14 alkaline batteries, see the battery
compartment for correct positioning.
50