Visit Installers guide EN - Flipbook - Sida 63
VISIT RECEIVERS
Visit alarm clock receiver
BE1580
Getting started
Buttons and controls
Time dial Visit LEDs
Snooze
Alarm dial
Alarm on/off
1 Pull the battery tab and connect the power supply to the alarm clock and the mains outlet.
Connect the bed shaker, tuck it under the pillow or mattress, and place the alarm clock on the bedside table.
Alarm indicator
Flash and sound
on/off
1
2
2 To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter.
3 The alarm clock lights up a Visit LED and starts to sound and flash. The bed shaker vibrates under the pillow or mattress.
If nothing happens, see Troubleshooting.
Time format
1
3
Wakeup
Flashes
Speaker
Night light
1 – 3.5 mm external trigger input
3 – Landline telephone
2 – Bed shaker
4 – Power supply
Default signal pattern
In the box
Dimensions and weight
BE1580 Visit alarm clock
Height: 108 mm, 4.3"
BE1270 Bed shaker
Width: 121 mm, 4.8"
Power supply
Depth: 92 mm, 3.6"
Mains power: 7.5 V DC / 1.5 A
External power supply unit
Backup batteries: 41.2 V AAA
NiMH rechargeable batteries
Orange LED, pacifier symbol
The baby monitor is activated
Battery backup operating time
~ 24 h when fully charged
Green LED, door symbol
The door transmitter is activated
Battery backup charging time
~ 10 h from fully depleted
Output signals
Yellow LED, telephone symbol
The phone transmitter is activated
Four high-intensity flashing LEDs
Bed shaker power: 2.0 – 4.0 VDC
When a transmitter is activated, the alarm clock lights up an LED, sounds, flashes and the bed shaker starts to vibrate with a
certain pace. This is called signal pattern. The transmitters determine the pattern, and the default is as follows:
Transmitter
Alarm clock
Bed shaker
Activated source
Visit LED
Sound
Flash
Vibration
Green
Yellow
Orange
Red
Orange and red
Door chime
Ring signal
Baby melody
Fire horn
Emergency alert
Yes
Yes
Yes
Yes
Yes
Slow
Medium
Fast
Long
Long
Door transmitter / push button transmitter
Telephone transmitter / connected telephone
Baby monitor
Smoke alarm
CO alarm
Environment
Changing the signal pattern
For indoor use only. Operating
temperature: 0° to 35° C, 32° to 95° F
The signal pattern can only be changed on the transmitters. See Changing the signal pattern for the relevant transmitter.
Relative humidity
15% to 90%, non-condensing
Settings
Accessories
Orange and red LEDs blink alternately
The CO alarm is activated
Red LED, fire symbol
Sound:100 dB @ 10 cm, 950 Hz – 3 kHz
The smoke alarm is activated
61
Frequency and coverage
Frequency: 314.91 MHz, 433.92 MHz
or 868.3 MHz, depending on region
Coverage by region:
315 MHz: Up to 50 m (164 ft)
433 MHz: 30 – 80 m (98 - 260 ft)
Weight: 390 g, 13.7 oz. incl. batteries
868 MHz: 50 – 250 m (55 - 273 yd)
Coverage depends on the radio
Visit LEDs
frequency, building’s characteristics
The Visit LEDs normally indicate
and the combination of transmitters
the following:
and receivers.
Power and battery
3
4
Technical specifications
41.2 V AAA NiMH batteries
2
BE1270 Bed shaker
BE9105 Telephone Cord
BE9250 Mobile phone sensor *
BE9023 Magnetic switch
BE9026 Contact mat
* Not available on all markets.
Flash and sound on/off
Press the flash and sound on/off button marked with
on the back of the alarm clock repeatedly to toggle between
the options. A
icon will appear on the clock face when the flash is turned off and a
icon when the sound is muted.
Display backlight
Press the button marked with
repeatedly to adjust the intensity in 4 steps. Step 5 results in permanent backlight.
Time format
Press the time format button marked with 12/24h on the back of the alarm clock to toggle between a 24h and a 12h setting.
62