Switch Product Catalogue 2020 - Catalog - Page 53
Blind Actuator for Roller Shutters, Blinds & Awnings
DALI 12-24VDC
Features
+ 2x normally open contacts 16 A 230V AC
+ Inrush current up to 165A/20ms
+ Energy-saving bistable relays
+ Casambi enabled wireless switches
+ Rich timer features
+ Flush-mounted housing
Technical details
+ 2 CH switch actuator
+ Control: Casambi
+ Switching type: 2x 16A / 165A inrush current
+ Construction: Flush mouted housing
+ Power supply: 130-240V AC 50/60Hz
+ Dimensions: 46,5 x 70(51) x 30 mm
1 Channel Constant Voltage Input LED Dimmer
1 Push Button Input
CBU-BOX with TED Trailing Edge
Dimmer module
CBU-BOX
Conduit box for connecting the CBU-TED
into mains wiring to ensure double insulation
standards are maintained.
LED Bus+Dimmer+Fader+Driver 1CH Constant
Voltage Input 12-24Vdc, Output 1x10A,
Command DALI, Analogic Auto Detection N.O
Push Button / 0-10V / 1-10V / Potentiometer
DALI 12-48VDC Input
1 Channel Constant Voltage Input LED Dimmer
1 Push Button Input
Led Bus+Dimmer+Fader+Driver 1CH Constant
Voltage Input 12-48Vdc, Output 1×6.5A,
Command DALI, Analogic Auto Detection N.O
Push Button / 0-10V / 1-10V / Potentiometer
Suits ASD, TED & LD220WCM modules
Loop-in loop-out push fit connections,
Easy access lid to connect supply on site
CBU-TED included Complete with 1 meter 3
pin 240V
Single Channel Relay
switching loads up to 10A
Ceiling Flush Mounted
PIR Sensor
CBU-RELAY is a single channel
relay, capable of switching loads
up to 10A (dependent on type
of load) via Casambi. Complete
with cable clamp providing strain
relief. Also available in a Normally
Closed variant.
This flush mounted sensor is suitable
for easy mounting through a 73/75mm
diameter hole into a ceiling void
which is at least 78mm deep. For
optimum coverage, mounting height
is recommended between 2.4m – 3m
giving a detection diameter of up to 7m.
The integrated light sensor can be used
for daylight dimming or as a photocell.
Suitable for most applications including
commercial, industrial, education, retail
hospitality and many more.
3-wire AC motor controller with
Casambi integration
The controller is calibrated within the software
to set the upper (open) and lower (closed) limits,
then using the integral timer movement, the
shade can be set anywhere within the limits.
XPRESS Switch 4 Button
Xpress is a wireless user interface that can be
configured via the Casambi app. The four target
buttons can control a scene or an animation of the
user’s choice or simply one luminaire, one luminaire
group or all lamps together if so desired.
Xpress has buttons for dimming. By once tapping
the ‘dim down’ button the chosen luminaire or
luminaire group will go to 0%. When the ‘dim up’
button is once tapped the luminaire or luminaire
group will instead go to 100%. By holding one of
the dim-buttons the luminaire or luminaire group
will dim smoothly.
Xpress is available in black or white and
magnetically attaches to a wall-mounting plate.
The switch can be operated in situ, or removed and
used as a remote, on a bed-side or coffee table.
EnOcean Square Double Switch – White
No mains, no battery EnOcean Module, Surface
Mounted Wireless Switch.
Lots more options available in the EnOcean range.
Please ask for more information.
These products are ideal where wiring is impossible.
Casambi Cloud Gateway for
remote connection – PSU
Receive data from your Casambi network
and remotely control it over the internet
with a Casambi Cloud Gateway. Based
on Raspberry Pi hardware, the Casambi
Cloud Gateway comes with Ethernet and
Wi-Fi connections for internet access. The
user interface is the Casambi App. (CBUGateway-PSU)
Battery Free Remote Control
8 Buttons
Battery-free remote control with 8
buttons. The remote control is installed
using NFC technology.
Technical facts:
+ Estimated lifetime:
50.000 actuations
+ Range: up to 10 m in the same room
+ Dimensions: 186,2 x 49 x 16 mm
53