D D Product Brochure 2019 V9 with hyperlinks Web - Flipbook - Page 16
16
17
A sleek, lightweight, low visual impact and easy to construct self-assembly screen
cover system suitable for all aquarium types.
There is nothing worse than coming down in the morning to finding your favourite fish
lying dead and crispy on the carpet. Many fish, especially wrasse, have a tendency to jump
from the tank at night or when frightened and chased by another fish and so a solution to
preventing the loss of such fish should be high on every fish keeper’s priority list.
Available in the following versions and are designed to be cut to size:
TC7575PRO - 75cm x 75cm nominal size.
TC12075PRO - 120cm x 75cm nominal size.
TC18075PRO - 180cm x 90cm nominal size.
The Jumpguard Pro Aquarium Cover consists of a kit of parts which allows the aquarist
to create a custom frame for their own specific aquarium. The rigid corners and extruded
aluminium sections create a very solid frame which sits neatly inside glass of the aquarium,
resting on the top lip.
Kit Contents: 4 x aluminium frame sections, 6 x plastic standard corners, 2 x plastic handles,
1 x length of rubber spline, 1 x sheet of black mesh, 1 x spline roller tool, 1 x instruction
manual, 2 x reverse corners to form flexi-cut-out, 1 x Brace bar (TC7575PRO),
2 x Brace bars (TC12075PRO), 3 x Brace bars (TC18090PRO) + clips and attachments.
www.theaquariumsolution.com
NEW PROFILE DESIGN
The special extruded aluminium profile is
shaped with a lip which sits directly onto the
edge of the glass, removing the requirement for
any additional clips or brackets. The section is
extruded then powder coated in a tough, low
sheen, black finish for greater scratch resistance
and greater aesthetics.
SPECIAL CORNERS INTEGRATE WITH
SILICONE JOINTS
The lower section of the corners is specifically
designed so that it does not interfere with the
silicone bead in the corners of your tank which
gives a tight fit to the glass with no gaps. It also
makes it easier and neater to cut off the corner
if you want to bring wires out at the back of the
tank for pumps and heaters.
NEW BLACK MESH WITH MAXIMUM
LIGHT PENETRATION
For those concerned about loss of light
penetration into your reef tanks, we tested light
levels with a Apogee MQ-200 meter and got the
following results:
PAR without cover around 390 - 400
PAR with cover around 380 - 390
Only an approximately 2.5% reduction in light with
no shadowing at all.
JUMPGUARD ACCESSORY SETS
Multi-Cut-out Set - TCMULTICO
Each Jumpguard Multi-Cut-out Set provides you with 3 different cut-out options to allow you
to modify the frame around any light brackets, cables or pipework etc.
Each kit contains: 1 pair of 15mm offset corners, 1 pair of 40mm offset corners,
1 x 40mm x 120mm lighting bracket or rigid cut-out.
The frame between the offset corners can be cut to length.
Brace Bar Set - TCBRACE
For larger aquariums or whenever fitting a Cut-out Set we recommend installation of one or
more brace bars to retain the structural integrity of the frame and to stop the outer edges
from pulling in together.
Each kit includes: 2 x 900mm x 12mm x 8mm brace bars, 2 x T piece connectors,
6 x connector clips
CODE
DESCRIPTION
TC7575PRO
JUMPGUARD PRO TANK COVER 75CM X 75CM
TC12075PRO
JUMPGUARD PRO TANK COVER 120CM X 75CM
Flexi-Cut-out Set - TCFLEXICO
The Jumpguard Flexi-Cut-out Set provides you with 2 standard corners and 2 reverse
corners to allow you to modify the frame around any larger overflow boxes, light brackets,
cables or pipework etc, that are too large to be covered by the Multi-Cut-out Set.
TC18090PRO
JUMPGUARD PRO TANK COVER 180CM X 90CM
TCBRACE
JUMPGUARD / JUMPGUARD PRO BRACE BAR SET
TCFLEXICO
JUMPGUARD / JUMPGUARD PRO FLEXIBLE CUT-OUT SET
Each kit Jumpguard PRO kit already contains the parts from one TCFLEXICO as standard.
TCMULTICO
JUMPGUARD / JUMPGUARD PRO MULTI CUT-OUT SET
www.theaquariumsolution.com
D - D P R O D U C T S J U M P G UA R D AQ UA R I U M C OV E R
D - D P R O D U C T S J U M P G UA R D AQ UA R I U M C O V E R
JUMPGUARD PRO AQUARIUM COVER